Showing posts with label Home DIY. Show all posts
Showing posts with label Home DIY. Show all posts

Monday, May 25, 2009

Sprinkler Valve

Each year, after sprinkler system winterization, something is always wrong when I restart the sprinkler system. This year, one zone turns on once there is water in the pipe even though the sprinkler controller is powered off, i.e., the sprinkler cannot be turned off. The reason is the bleed valve was not completely shut off. One indicator of this problem is water appears in the valve box. In the photo below, there are 3 valves in the valve box. The bleed valves are the small black ones.


Tuesday, March 3, 2009

Dishwasher Drain Hose Connection

Our dishwasher is connected according to the following diagram except that the sink drain and dishwasher drain outlets are connected in the horizontal portion of the drain pipe. When the dishwasher is not used for long time, its P-trap may get clogged.









Here is another diagram for dishwasher drain hose connection:








Both diagrams are from plumbing-troubleshooter.com.

Sunday, February 22, 2009

Coat Hanger Antenna

I build a coat hanger antenna over the weekend to receive over-the-air TV channels. All materials and parts I use are from old stuffs or spare parts. The total cost for the project is $0. The design is based on that described in this file. I use six copper wire coat hangers, 13 screws, 10 washers, one transformer, one Nylon cable clamp, one wood board and two metal fittings. I place the antenna in the attic and connect the cable to the Tivax TV converter box. The antenna brings in total 31 channels. The signal strength for most channels is between 40 and 80.

Thursday, February 19, 2009

Waterproofing Basement

I read about using Drylok paint to seal the walls in the basement. Drylok is a paint/sealant that forms a strong barrier against moisture and can be used on cement block. Five coats of Drylok are recommended. Drylok coating also helps to lower the humidity in the basement.

Monday, February 16, 2009

Honda Pilot Front Brake Pad DIY

I changed the front brake pads of my 2004 Honda Pilot this morning. The pilot has 40,000 miles on it. The new Prostop brake pads cost $19.25 including tax, which I bought from Pepboys.
I step on the manual brake to brake the car, open the lid of brake fluid container and then loose the five screws on the wheel helped by using a long metal pipe. I jack up the Pilot using the tools provided by the car. There are short metal pieces underneath the car for this purpose (don't use the door step portion). The suspension of the front wheel is flexible. The wheel does not immediately go up with the body of the car. The body of the car needs to be jacked up enough in order for the wheel to be off the ground. I take all screws off the wheel and take the wheel off.
There are two 12mm screws that hold the caliber. I use a circular wrench fitting in the tool box to unscrew them. The caliber needs to be supported after it is off the base. I then take the old brake pads off (the thickness is about 40% of that of the new pads) and put the new pads on. I use the brake tool to push the caliber piston back, put the caliber back over the new pads, then screw and tighten the two caliber screws. I put wheel on, screw on the five wheel screws by hand, lower the car and then firmly tighten the wheel screws.
I close the lid of brake fluid container, release the manual brake and step on the car brake several times to engage the new pads.
It takes me 2.5 hours to change brake pads on both front wheels. I watched a video and read a step-by-step instruction before the job.

Saturday, February 14, 2009

Fix ABS Pipe Leakage

I fixed the ABS pipe leakage problem in the basement. The pipe connects kitchen sink to the main sewer pipe.
The only tool I bought was a PVC/ABS handsaw. The materials I bought included two 2" heavy duty no hub couplings, one 2" ABS 45 degree elbow, one 2"x10' ABS DWV pipe and 4 oz black ABS cement. The total cost including tax is $38.02.
I cut two pieces of ABS pipe several inches each and apply ABS cement to connect these two pieces to the 45 degree elbow. I make a 1/4 turn after pushing the ABS pipe into the elbow and firmly hold them for more than 1 minute. The ABS cement has a very strong smell and use of it should be in a well ventilated area. I wait a couple of hours before I cut the portion of ABS pipe with problem using the PVC/ABS handsaw. I leave 1/4" margin on each side. Then I put no hub couplings on the pipe and roll one half of it in order to be able to fit the new elbow section I made. Once everything is in place, I tighten the metal clamps for each coupling. To minimize the chance of leakage in the future, I make sure the bottom half of each connection have a tighter fit.

Monday, February 9, 2009

Fernco Clamps

There is a slight leak around one of the joints of PVC pipe in the basement. The PVC pipe is connected to the kitchen sink. One easy fix is to buy a Fernco flexible elbow or two Fernco clamps with a PVC elbow.
According to the product description from Home Depot: "These high quality flexible couplings let you connect all common household drain, waste, and vent pipes quickly and easily without using special tools or fittings. They're the ideal replacement for fittings cut out at the joint during alteration or repair. These connectors are easily installed by tightening the 300 series stainless clamps. Made from flexible polyvinyl chloride these connectors fit cast iron, steel, plastic, cooper and lead."
I read about bell & spigot joints and here is the definition of spigot: "The end of a pipe that is inserted into an enlarged end of another pipe to form a joint." Another note: "When inserting a pipe between two fixed ends, cut the new piece to leave an 1/8-in. gap at both joints."

Saturday, February 7, 2009

Water Heater Flue Pipe Installation

The tools I bought for the job include one 5-blade crimper and one 3-piece snip set. The materials I needed include two 6"x24" pipe, one 4"x24" pipe, one 6"x6"x6" tee, one 6" elbow, two 4" elbow, one 6"x5" reducer, one 6"x4" reducer, 50 sheet metal screws and one duct tape. Total cost including tax: $83.81.
I removed the old pipes for the water heater as well as a section for the furnace first. Taking sheet metal screws off the old pipes is not easy. The installation can be done by one person, but a second hand will be helpful. One annoying fact is elbows are easy to fall apart when falling to ground and it is very hard to fit it back in. To prevent exhaust leakage, the crimped side of a pipe is fit into the uncrimped side of a pipe in the path of the exhaust direction. I used a 9/64" drill bit to pre-drill into the connections and then screwed sheet metal screws in. Some pressure needs to be applied when drilling into metal. I tried to wrap the connections with duct tape. However, since the pipes are very close to the furnace, they become hot when the furnace is on. I decided not to use duct tape.



Wednesday, February 4, 2009

Notes on Vent Pipe Installation

Wear work gloves when working with sheet metal with sharp edges. Make cuts before rolling the sheet into a pipe. Cutting round pipe is difficult. Pre-drill 3 holes 120 degree apart and use sheet metal screws to connect the pieces. Use aluminum duct tape to seal the joints. Use Master Flow's flexible duct connector available at Home Depot to join the sections without crimped ends.

Sunday, February 1, 2009

Water Heater Duct

The flue pipe for our new water heater failed the township inspection. According to the local plumbing code, the diameter of the flue pipe should be 4". To fix the problem, we need to buy two 4" elbows, one 12" long 4" pipe, one 6" to 5" reducer plus 4" wye tee, one 30" long 6" pipe and one 6" elbow. Audubon Plumbing Supply sells these pipes and fittings. However, since this is the first time I work on stuff like this, I will buy from local Lowes or Home Depot because of their return policy.